Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 250 | Manualshive

Страница: 250 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 250

Symptom:

P0645-A/C CLUTCH RELAY CIRCUIT

When Monitored and Set Condition:

P0645-A/C CLUTCH RELAY CIRCUIT

When Monitored:

With the ignition on. Battery voltage greater than 10 volts. A/C Switch

on.

Set Condition:

An open or shorted condition is detected in the A/C clutch relay control

circuit. One Trip Fault.

POSSIBLE CAUSES

A/C CLUTCH RELAY OPERATION

(A17) FUSED IGNITION SWITCH OUTPUT CIRCUIT

A/C CLUTCH RELAY RESISTANCE

(C28) A/C CLUTCH RELAY CONTROL CIRCUIT OPEN

(C28) A/C CLUTCH RELAY CONTROL CIRCUIT SHORT TO GROUND

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t

, actuate the A/C Clutch Relay.

Is the A/C Clutch Relay operating?

All

Yes

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 2 - NGC.

No

→

2

Turn the ignition off.
Remove the A/C Clutch Relay from the PDC.
Ignition on, engine not running.
Measure the voltage on the (A14) Fused Ignition Switch Output circuit in the PDC.
Is the voltage above 11.0 volts?

All

Yes

→

No

→

Repair the open or short to ground in the (A17) Fused Ignition
Switch Output circuit. Check and replace any open fuses.
Perform POWERTRAIN VERIFICATION TEST VER - 2 - NGC.

244

DRIVEABILITY - NGC

«
...
248
249
250
251
252
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов