Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 298 | Manualshive

Страница: 298 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 298

Symptom:

U0168-NO SKIM BUS MESSAGES

When Monitored and Set Condition:

U0168-NO SKIM BUS MESSAGES

When Monitored:

Ignition on or Engine Running.

Set Condition:

No BUS messages are received from the SKIM for 20 seconds.

POSSIBLE CAUSES

INTERMITTENT CONDITION

PCI BUS CIRCUIT OPEN FROM PCM TO SKIM

LOSS OF SKIM COMMUNICATION

SKIM/PCM

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t

, read the DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→

No

→

2

Turn the ignition on.
With the DRB III, attempt to communicate with the SKIM.
NOTE: This test will indicate if the Bus is operational from the DLC to the
SKIM.
Was the DRB III able to communicate with the SKIM?

All

Yes

→

No

→

Refer to symptom BUS +/- SIGNAL OPEN FROM SKIM in the
COMMUNICATION category.
Perform SKREEM VERIFICATION TEST - VER 1A.

3

Turn the ignition off.
Disconnect the PCM harness connectors.
Disconnect the SKIM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the PCI Bus circuit from the SKIM harness connector to
the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→

No

→

Repair the PCI Bus circuit between the PCM and the SKIM for an
open.
Perform SKREEM VERIFICATION TEST - VER 1A.

292

DRIVEABILITY - NGC

«
...
296
297
298
299
300
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов