manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 168 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 168

TEST

ACTION

APPLICABILITY

2

Perform a visual and physical inspection of the entire Evaporative Emission system.
Check for the following conditions:
- Hoses disconnected or left off
- Holes or cracks
- Loose seal points
- Evidence of damaged components
- Incorrect routing of hoses and tubes
- Fuel Cap left off or bad gasket seal
Were any of the above conditions found?

All

Yes

→

Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

3

3

Turn the ignition off.
Carefully inspect the Evap Purge Solenoid vacuum supply hose for proper routing.
Check for a pinched or plugged hose from the throttle body to the Purge Solenoid.
Ensure the vacuum port at the throttle body is free from any blockage.
Were any problems found?

All

Yes

→

Repair the vacuum supply, hose/tube as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

4

4

Disconnect the vacuum supply hoses form the EVAP Purge Solenoid.
Using a hand vacuum pump, apply 10 in Hg to the

9

CAN

9

side of the EVAP Purge

Solenoid.
Ignition on, engine not running.
Observe the vacuum gauge.
With the DRBIII

t

, actuate the EVAP Purge Solenoid .

Does the vacuum drop when the solenoid is actuated?

All

Yes

→

Go To

5

No

→

Replace the Evap Purge Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

5

Reconnect all vacuum hoses.
Start the engine and allow it to idle.
Using the DRBIII

t

, perform the NVLD FORCED MONITOR TEST.

Monitor the NVLD Switch state.
NOTE: As the test runs, the NVLD Switch should go from an OPEN state to
CLOSED. After the vacuum is released from the EVAP system the Switch
state will return to OPEN.
Did the NVLD Switch operate as described above?

All

Yes

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

6

162

DRIVEABILITY - NGC

P0440-GENERAL EVAP SYSTEM FAILURE —

Continued

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов