manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 249 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 249

Symptom:

P0633-SKIM KEY NOT PROGRAMMED IN PCM

When Monitored and Set Condition:

P0633-SKIM KEY NOT PROGRAMMED IN PCM

When Monitored:

Ignition on.

Set Condition:

The SKIM Key information has not been programmed into the PCM.

POSSIBLE CAUSES

PROGRAMMING SKIM KEY INTO PCM

VERIFY PCM PROGRAMMING

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t

, erase DTCs.

Using the DRBIII

t

, program the SKIM Key information into the PCM.

Start the engine.
NOTE: If the engine will not start, crank the engine over for 15 seconds.
Crank at least 2 times with the ignition switch returning to the off position
each time.
Allow the engine to reach normal operating temperature.
With the DRBIII

t

, read DTCs.

Does the DTC reset?

All

Yes

→

Go To

2

No

→

The SKIM KEY information has been succcessfully programmed
into the PCM. Test is complete.
Perform SKREEM VERIFICATION TEST - VER 1A.

2

NOTE: The ignition switch must be left in the off position for a minimum of
10 seconds.
Cycle the ignition switch to the off position and then back to run.
Attempt to program the PCM with the applicable information.
Start the vehicle and allow it to reach normal operating temperatures.
With the DRBIII

t

, read DTCs.

Does the DTC reset?

All

Yes

→

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform SKREEM VERIFICATION TEST - VER 1A.

No

→

The SKIM Key Information has been successfully programmed
into the PCM. Test is complete.
Perform SKREEM VERIFICATION TEST - VER 1A.

243

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов