Chattanooga Group OPTIFLEX3 2090 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 48

background image

24

OptiFlex® 3 Continuous Passive Motion (CPM) Therapy Unit

A. Part Number

. . . .

. . . . . . . . . . . . . . . . . . . . . . . . J2004

B. Tools and Equipment Required

5/64" Allen wrench
#2 Phillips screwdriver
Gear Puller
Snap Ring Pliers
5/16" Socket Driver
Large Flathead Screwdriver
Needle Nose Pliers
Molygraph Grease

NOTE:

Refer to

Section B

of each sections referenced

below for additional tools needed.

C. Acme Rod Removal & Replacement

1. Refer to

Section 6.1, parts C and D

, Rear

Cover and Front Cover Removal and

Replacement to remove the Covers of the

unit.

2. Refer to

Section 6.4, part C

, Drive Belt

Removal and Replacement, to remove the

Drive

Belt.

3. Using a 5/64" Allen wrench, remove the set

screw from the Pulley attached to the Ball

Screw.

NOTE:

Retain all rivets, nuts, washers, bearing and

screws for installation of the Ball Screw.

4. Use a gear puller to remove the Pulley from

the Ball Screw.

NOTE:

Using a gear puller should decrease the

possibility of damage to the Pulley.

5. Remove the 2 washers and the bearing

from the end of the Ball Screw.

Refer to

Figure

6.12.

•
•
•
•
•
•
•
•

7. Using a 5/16" Socket Driver remove the 4

nuts and washers securing the Base

Plate at the end of the Frame Base.

Refer to

Figure

6.14.

6. Using a #2 Phillips screwdriver, remove

the screw on each side of the Frame Base to

release the Base.

Refer to Figure 6.13.

SCREW SECURING BASE

TO THE FRAME BASE

FIGURE 6.13

FIGURE 6.14

8. Using a large Flathead screwdriver, gently

pry the plate off of the Ball Screw.

Refer to

Figure

6.14.

NUTS SECURING

BASE PLATE

PLACE FLATHEAD

SCREWDRIVER BEHIND

THIS PLATE

Unplug the unit from the power source before
attempting any removal or replacement procedures
to prevent electrical shock.

NOTE:

Observe the locations of the washers and

bearing for installation.

Inset

A on page 38

details proper installation.

WASHERS

BEARING

FIGURE 6.12

6 REMOVAL & REPLACEMENT

Failure to re-install and properly tighten all
screws may result in Electrical Safety System
degradation which may cause unit damage,
malfunction, electrical shock or personal injury.

6.8 ACME ROD (BALL SCREW)

«
...
24
25
26
27
28
...
»

Содержание OPTIFLEX3 2090

















































Отзывы:

Нет отзывов

Похожие инструкции для OPTIFLEX3 2090

Бренд: Palazzetti Страницы: 112

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Xtool Страницы: 51

Бренд: H-TEC Education Страницы: 16

Бренд: H-TEC Education Страницы: 12

Бренд: Rane Страницы: 38

Бренд: Kartsana Страницы: 36

Бренд: Qlight Страницы: 3

Бренд: qtran Страницы: 2

Бренд: Q-Optics Страницы: 2

Бренд: Garden Treasures Страницы: 2

Бренд: rbd instruments Страницы: 18

RZN 43-E Series

Бренд: D+H Страницы: 2

Бренд: Kanlux Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды