Chattanooga Group OPTIFLEX3 2090 Скачать руководство пользователя страница 17

Страница: 17 / 48

OptiFlex® 3 Continuous Passive Motion (CPM) Therapy Unit

5 TROUBLESHOOTING

5.8 TRAVEL SPEED TEST

Spec

. . . . . . . . . . . . . . . . . . . . . . 0° to 90° in 60 Sec ±10%

of seconds

A. Equipment Required

Calibrated stop watch

B. Test

Set unit up as described in the “Flexion Angle

Test."

Adjust the Femur Bar length to 34 and

tighten.

Move to 0° by pressing the Emergency

Start/Stop button. When motion stops and

Display reads 0°, press the Emergency Start/

Stop button to stop the unit. Then,

simultaneously press the Emergency Start/

Stop button and the stop watch start button.

The unit should move from 0° to 90°

within the specification listed above.

Repeat three times. Calculate and Record

the

average.

If unit fails test, troubleshoot the following

components and replace if necessary:

Check Pendant Cable connector to Motor

Control Board

Motor Control Board

Pendant

Motor Assembly

Drive Belt

Pulleys

5.9 EMERGENCY START/STOP FUNCTION TEST

Spec

. . . . . . . . .Unit start or stop upon pushing button

A. Equipment Required

OptiFlex3 with Pendant

B. Test

Place unit on a level work surface.

Plug unit power cord into grounded wall

outlet with appropriate voltage. See

Specifications

page 8.

Connect Pendant to unit and turn unit power

ON.

Press the Emergency Start/Stop button to start

and stop the unit. Repeat several times.

If unit fails test, troubleshoot the following

components and replace if necessary:

Pendant Cable connector to Motor

Control Board.

Motor Control Board.

Pendant.

5.10 PENDANT DISCONNECT TEST

Spec

. . . . . . . . . . . . . . . . . .Unit stops immediately

upon Pendant disconnect

A. Equipment Required

OptiFlex3 with Pendant

B. Test

Place unit on a level work surface.

Plug unit power cord into grounded wall

outlet with appropriate voltage. See

Specifications

page 8.

Connect Pendant to unit and turn unit

power

ON.

Press the Emergency Start/Stop button to

start the unit.

Disconnect the Pendant from the unit while

moving. Unit should stop.

If unit fails test, troubleshoot the following

components and replace if necessary:

Pendant Cable connector to Motor

Control

Board

Motor Control Board

Pendant

Содержание OPTIFLEX3 2090

















































Результаты поиска

Содержание OPTIFLEX3 2090

Отзывы:

Похожие инструкции для OPTIFLEX3 2090

Бренды по названию

Популярные бренды

Chattanooga Group OPTIFLEX3 2090, Руководство по обслуживанию

Результаты поиска

Содержание OPTIFLEX3 2090

Отзывы:

Похожие инструкции для OPTIFLEX3 2090

Бренды по названию

Популярные бренды