Chattanooga Group OPTIFLEX3 2090 Скачать руководство пользователя страница 30

Страница: 30 / 48

OptiFlex® 3 Continuous Passive Motion (CPM) Therapy Unit

Disconnect the pendant from the unit before
attempting any removal or replacement procedures
to prevent electrical shock.

6 REMOVAL & REPLACEMENT

6.11 PENDANT CONTROL BOARD

A. Part Number

. . . . . . . . . . . . . . . . . . . . . . . . . . .J1102

B. Tools and Equipment Required

#1 Phillips Screwdriver

NOTE:

Refer to

Section B

of the section referenced

below for additional tools needed.

C. Pendant Control Board Removal &

Replacement

Refer to

Section 6.10, part C, Pendant Cable

Removal and Replacement

to open the

Pendant and remove the Cable.

2. Using a finger nail, lift the brown plastic bar

securing the Display Ribbon Cable to the

Control Board. Slide the Ribbon Cable back to

free from the Control Board.

Refer to

Figure

6.23.

•

FIGURE 6.23

LCD RIBBON

CABLE

PLASTIC BAR

SECURING RIBBON CABLE

3. Disconnect the 2 Pin connector harness

from the Display attached to the Control

Board.

Refer to Figure 6.24.

FIGURE 6.24

2 PIN CONNECTOR

HARNESS

SCREWS SECURING

CONTROL BOARD

22 TOTAL

BATTERY

4. Using a #1 Phillip screwdriver, remove the 22

screw securing the Control Board to the

Pendant

Base.

Refer to Figure 6.24.

NOTE:

Carefully slide the Display Ribbon Cable

through the slot in the Control Board when

removing the board. Handle the Ribbon

Cable gently to avoid damage.

Lift the Control Board to remove.

6. Reverse for installation.

NOTE:

During installation of the Control Board,

do not pinch the 2 Pin Connector Harness

from the display to the Control Board by

running it between the Display and the

Control Board. Pinching the Harness may

result in the loss of the Back Light.

Содержание OPTIFLEX3 2090

















































Результаты поиска

Содержание OPTIFLEX3 2090

Отзывы:

Бренды по названию

Популярные бренды

Chattanooga Group OPTIFLEX3 2090, Руководство по обслуживанию

Результаты поиска

Содержание OPTIFLEX3 2090

Отзывы:

Бренды по названию

Популярные бренды