Chattanooga Group OPTIFLEX3 2090 Скачать руководство пользователя страница 24

Страница: 24 / 48

OptiFlex® 3 Continuous Passive Motion (CPM) Therapy Unit

6 REMOVAL & REPLACEMENT

NOTE:

To order a replacement Potentiometer, order all

three parts listed in

section A.

A. Part Numbers

Potentiometer

. . . . . . . . . . . . . . . . . . . . . . . . . J6040

Split

Pin

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J6023

Nylon

Covers

. . . . . . . . . . . . . . . . . . . . . . . . . . J6022

B. Tools and Equipment Required

3/32" Allen Wrench
#2 Phillips Screwdriver
Heyco Tool #29
Fine edged tool
Small Flathead Screwdriver

NOTE:

Refer to

Section B

of each sections

referenced below for additional tools needed.

C. Potentiometer Removal & Replacement

1. Refer to

Section 6.1, parts C and D

, Rear

Cover and Front Cover Removal and

Replacement to remove the Covers of the

unit.

2. Use a fine edged tool to lift the Decal

on the Potentiometer and remove.

Refer to

Figure

6.9.

NOTE:

Save the Decal, J6107, for installation of the

replacement

Potentiometer.

•
•
•
•
•

Unplug the unit from the power source before
attempting any removal or replacement procedures
to prevent electrical shock.

POTENTIOMETER

DECAL

COVER

SCREWS

3. Use a #2 Phillips screwdriver to remove the 3

screws securing the Potentiometer Cover and

remove the Cover.

NOTE:

When installing the Potentiometer Cover, part

number J6105, hand tighten the three

screws until snug. Overtightening the screws

will crack the Cover.

4. Using a 3/32" Allen wrench remove the two

cleat

screws.

Refer to Figure 6.10

5. Using a Heyco Tool, squeeze the sides of the

Heyco and pull out to remove.

Refer to

Figure

6.10.

6. Using a small Flathead screwdriver positioned

behind the Potentiometer, apply just enough

pressure to free the Potentiometer.

Refer to

Figure

6.10.

NOTE:

On the back of the Potentiometer, make

certain that the Nylon Covers, part number

J6022, on each side of the split pin are

installed.

Refer to Figure 6.11

SMALL

SCREWDRIVER

CLEAT

HEYCO

FIGURE 6.9

FIGURE 6.10

FIGURE 6.11

SPLIT PIN WITH

NYLON COVERS

Failure to re-install and properly tighten all
screws may result in Electrical Safety System
degradation which may cause unit damage,
malfunction, electrical shock or personal injury.

6.7 POTENTIOMETER (KNEE-POT)

Содержание OPTIFLEX3 2090

















































Результаты поиска

Содержание OPTIFLEX3 2090

Отзывы:

Похожие инструкции для OPTIFLEX3 2090

Бренды по названию

Популярные бренды

Chattanooga Group OPTIFLEX3 2090, Руководство по обслуживанию

Результаты поиска

Содержание OPTIFLEX3 2090

Отзывы:

Похожие инструкции для OPTIFLEX3 2090

Бренды по названию

Популярные бренды