Chattanooga Group OPTIFLEX3 2090 Скачать руководство пользователя страница 18

Страница: 18 / 48

OptiFlex® 3 Continuous Passive Motion (CPM) Therapy Unit

6 REMOVAL & REPLACEMENT

6.1 UNIT COVERS

A. Part Number

Push Rivet (Male & Female Components). . J6004

Rear Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J6089

Front Access Cover. . . . . . . . . . . . . . . . . . . . . . . J6103

B. Tools and Equipment Required

Miniature Diagonal Cutters

C. Rear Cover Removal and Replacement

NOTE:

Miniature Diagonal Cutter are used only to

remove the Rivets. They are not intended to

cut the Rivets. Only apply enough pressure to

grasp the Rivet. They will be used to

re-install

the

Cover.

NOTE:

If Carriage is close to full extension, there may

not be sufficient clearance to remove the

Cover. For inoperable units,

refer to Section

6.2 Manual Movement of the Carriage

for

carriage

adjustment.

1. Using a pair of miniature diagonal cutters

remove the 11 Rivets securing the Rear or

Motor Cover. Grasp the Rivets from behind and

gently pry the Rivets up to release. This will

release both the male and female parts of the

Rivet.

Refer to Figure 6.1.

•

2. Lift up and rotate the Rear Acess Cover toward

the Carrying Handle of the unit. Slide the

cover over the Carrying Handle to completely

remove from the unit.

3. To install the Rear AcessCover, reverse the

above

steps.

D. Front Access Cover Removal and

Replacement

NOTE:

Miniature Diagonal Cutter are used only to

remove the Rivets. They are not intended to

cut the Rivets. Only apply enough pressure to

grasp the Rivet. They will be used to

re-install

the

Cover.

NOTE:

If Carriage is close to full extension, there may

not be sufficient clearance to remove the

Cover. For inoperable units,

refer to Section

6.2 Manual Movement of the Carriage

for

carriage

adjustment.

1. Using a pair of miniature diagonal cutters

remove the 8 Rivets securing the Rear or

Motor Cover. Grasp the Rivets from behind

and gently pry the Rivets up to release. This

will release both the male and female parts of

the

Rivet.

2. Lift to remove.

3. Reverse above steps to install.

Unplug the unit from the power source before
attempting any removal or replacement procedures
to prevent electrical shock.

FIGURE 6.1

Содержание OPTIFLEX3 2090

















































Результаты поиска

Содержание OPTIFLEX3 2090

Отзывы:

Бренды по названию

Популярные бренды

Chattanooga Group OPTIFLEX3 2090, Руководство по обслуживанию

Результаты поиска

Содержание OPTIFLEX3 2090

Отзывы:

Бренды по названию

Популярные бренды