manualshive.com logo in svg

Chattanooga Group OPTIFLEX3 2090, Руководство по обслуживанию

Поделиться
Скачать
Chattanooga Group OPTIFLEX3 2090 Скачать руководство пользователя страница 14

12

OptiFlex® 3 Continuous Passive Motion (CPM) Therapy Unit

5 TROUBLESHOOTING

5.3 VISUAL INSPECTION

A. General

 

Visually inspect the OptiFlex3 for and visible 

 

damage to the unit or pendant that may interfere 

 

with operation of the unit. Make sure that all 

 

screws are secure. Verify that the appropriate hook 

 

or loop fastener is secured to the carriage.

 

Check for proper labeling. Make sure that the 

 

Femur adjustment decals are in good condition. 

 

Verify that the serial decal for the unit is present.

 

Verify that the LCD lens is in good condition and 

 

clean if necessary. 

 

Verify that the domed heads of the femur hinge 

 

rivets are in good condition. Make sure that 

 

the hinges are secure, by attempting to pull them 

 apart.

5.4 FUNCTIONAL INSPECTION

 

Check the calibration of the unit by running it 

 

successively through its full ROM with femur length 

 

adjusted first to maximum and then to its 

 minimum 

length.

 NOTE:

 

Verify that the lead screw is unobstructed and no 

 

abnormal noises are present during operation.

 

Disconnect the pendant while the unit is running 

 

to verify that the unit will stop.

 

Perform the Speed test found on 

page 15. 

 

Clears all settings by activating the Reset.

5.5 ELECTRICAL SAFETY

 The 

OptiFlex3 has been tested to UL 60601-1, 

 

Standard for Safety for Medical Equipment.

 NOTE:

The device complies with current leakage, ground 

 

continuity, and dielectric withstand (Hi-Pot) limits 

 

as prescribed by IEC/EN/UL 60601-1 and C22.2 No. 

 

601.1-M90 w/A2 Medical Electrical, Part 1: General 

 Requirements 

for 

Safety.

 

Facility, local and national limits and test methods 

 may 

vary.

A. Power Requirements

Model: 2090 ..................................................... Input: 100-240 VAC

 

                                                                

50/60 HZ, 75 VA

5.6 ELECTRICAL SAFETY TESTS

 

Conduct all necessary Electrical Safety tests as 

 

required per your facility, local or national 

 

regulatory agency. In the USA follow NFPA 99 

 

(National Fire Protection Association) "Health care 

 Facility" 

standards.

NOTE:

Use the rivet shown in 

Figure 5.1 

as a connection 

 

point for Grounding Tests.

A unit failing dielectric withstand and/or leakage 
tests could indicate serious internal system 
problems. Do not place unit back into service. 
Contact the factory for repair. Do not attempt to 
repair the unit in the field.

This unit must not be operated with any 
adapter attached to the three prong plug 
that would disable the earth connection. 
Disruption of the earth connection may cause 
unit damage, malfunction, electrical shock, fire, 
or personal injury. 

Rivet 

FIGURE 5.1

Содержание OPTIFLEX3 2090

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды