manualshive.com logo in svg

Carlisle Ransburg DynaFlow 77376, Руководство по обслуживанию, Страница: 84 / 96

Поделиться
Скачать
Carlisle Ransburg DynaFlow 77376 Скачать руководство пользователя страница 84

ADDENDUM B:

Remote Operator's Panel

If the Model A12233 control console and Model  A12182 

Interface Panel is used, the optional Remote Operator 

Panel (P/N:  A11095) can be used.  this Remote Operator's 

Panel (shown above) operates in the following manner:

Color Select 

- This is an eleven position selector switch that 

allows the operator to select the next color to be loaded.  

If the most counter-clockwise position is selected (Solv) 

and the Paint (Solvent) Fill button is pushed, the normal 

load sequence occurs and solvent is loaded into the fluid 

sytem as if it was a color.

Paint (Solvent) Fill/Filled

 - This is a green illuminated 

push-button.  When pushed, the paint load sequence runs 

(as programmed from the "Load" user interface screen). The 

green indicator lamp flashes as the sequence is occurring 

and stays lit solid when the sequence has completed, 

indicating to the operator that the system is ready.

If there is already a color loaded (i.e., one of the color 

valve outputs is already on) when this button is pushed, 

the system will execute a flush sequence, followed by a 

load sequence.

Purge/Purged

 - This is an amber illuminated push-button.  

When pushed, a purge sequence is initiated (as programmed 

from the "Purge" user interface screen).  While the purge 

sequence is occurring, this indicator lamp flashes.  It remains 

on solid when the purge sequence is complete, indicating 

to the operator that the purge is complete.  This indicator 

will be turned off if a "Paint (Solvent) Fill" sequence has 

been initiated or a color is loaded.

NOTE

 

†

If both the green Paint (Solvent) Fill/Filled lamp 

and  the  amber  Purge/Purged  lamps  are  flashing 

simultaneously, this indicates that no sequence has 

been downloaded to the color change sequencer 

since the last time power was applied to the system.  

This can be corrected by loading a job from the user 

interface  screen  and  executing  at  least  one  fill  or 

purge sequence.

Return To Contents

LN-9400-00-R11  (08/2018)

84 / 96

www.carlisleft.com

APPENDIX

Содержание Ransburg DynaFlow 77376

































































































Отзывы:

Нет отзывов