Carlisle Ransburg DynaFlow 77376 Скачать руководство пользователя страница 12

Страница: 12 / 96

NOTE

Refer to Addendum C for complete information

regarding the flow limitations of the DynaFlow

Channel cards.

NOTES:

1. If the output of Gun 2 supplies one or more hand guns,

then Gun 2 should be operated in Manual mode using a

CCV for the Master Channel flow controller.

2. If the output of Gun 2 supplies a single applicator, then an

MVR should be used for the Master Channel flow controller

and Gun 2 should be operated in Auto mode.

3. If the output of Gun 2 supplies multiple appl-icators other

then hand guns, then Gun 2 should be operated in Manual

mode using a CCV for the Master Channel flow controller.

Additional Guns should be configured for each applicator

as shown below to provide automatic flow control for each

applicator.

Gun 3 through 6 =

Master Channel =

Material = Output of Gun 2

(Resin + 2

+ 3

Components)

Flow Controller = DR1

Flow Meter = Gear-Type

Operating Mode = Auto

Return To Contents

LN-9400-00-R11 (08/2018)

12 / 96

www.carlisleft.com

INTRODUCTION

Содержание Ransburg DynaFlow 77376

































































































Результаты поиска

Содержание Ransburg DynaFlow 77376

Отзывы:

Carlisle Ransburg DynaFlow 77376, Руководство по обслуживанию, Страница: 12 / 96

Результаты поиска

Содержание Ransburg DynaFlow 77376

Отзывы: