Carlisle Ransburg DynaFlow 77376 Скачать руководство пользователя страница 68

Страница: 68 / 96

Figure 7: Card Rack Assembly

77383-01

Rack Assembly, Empty, 1/2 Rack, 1 Mother Board

77383-02

Rack Assembly, Empty, Full Rack, 1 Mother Board

77383-03

Rack Assembly, Empty, Full Rack, 2 Mother Boards

77377-02

Interface Module Assembly, With RIO

A10946-01

Channel Module for use with 0-10VDC transducers and for the flow rate indication output

A10946-02 Channel Module for use with 0-10VDC or 4-20mA transducers and for the flow rate indication output

77378-00

Mother Board Assembly

LBAL0021-00 Interface Cable Assembly, Interface Panel to Control Panel, 40 ft.

LBAL5001-00 Interface Panel, Standard Two Component

LBAL5001-01 Interface Panel, GUN 1

LBAL5001-02 Interface Panel, GUN 2

A12182

Interface Panel W/Color Change

LPNE5002-00 Pneumatic Color Change Panel

LBAL5003-00 Pneumatic Operator Panel

Note:

Refer to the "DynaFlow Operator Interface" manual for parts that are specific to the 77376

and A12233 Stand-Alone Control Panel.

SYSTEM COMPONENTS

Item #

Part #

Description

DYNAFLOW SYSTEM COMPONENTS / PARTS IDENTIFICATION

(Figure 7)

Return To Contents

LN-9400-00-R11 (08/2018)

68 / 96

www.carlisleft.com

MAINTENANCE

Содержание Ransburg DynaFlow 77376

































































































Результаты поиска

Содержание Ransburg DynaFlow 77376

Отзывы:

Carlisle Ransburg DynaFlow 77376, Руководство по обслуживанию, Страница: 68 / 96

Результаты поиска

Содержание Ransburg DynaFlow 77376

Отзывы: