manualshive.com logo in svg

Carlisle Ransburg DynaFlow 77376, Руководство по обслуживанию, Страница: 3 / 96

Поделиться
Скачать
Carlisle Ransburg DynaFlow 77376 Скачать руководство пользователя страница 3

CONTENTS

SAFETY:  

4-8

Safety Precautions

  ................................................................................................................................................4

Hazards / Safegaurds

  ............................................................................................................................................5

INTRODUCTION:  

9-16

Features

 ................................................................................................................................................................ 9

Description

............................................................................................................................................................. 9

Block Diagram

 ..................................................................................................................................................... 13

Specifications

 ...................................................................................................................................................... 14

INSTALLATION:  

17-28

System Guidelines

 ..............................................................................................................................................17

Block Diagram For A Single-Component Gun

 .....................................................................................................19

Block Diagram For A Two-Component Gun

 .........................................................................................................20

Block Diagram For A Three-Component Gun

 ......................................................................................................21

Input Power

..........................................................................................................................................................22

Interfacing To The Flow Controller

. ......................................................................................................................23

Mother Board Terminals, Hardware Configuration, Transducers

 .........................................................................27

OPERATION:  

29-46

Overview

 ............................................................................................................................................................. 29

Parameter Descriptions

 ....................................................................................................................................... 30

Automatic Gun Applications

................................................................................................................................. 42

Manual Hand Gun Applications

 ........................................................................................................................... 43

General

 ................................................................................................................................................................ 44

Job Select Timing Diagram

.................................................................................................................................. 46

Troubleshooting Guide

 ........................................................................................................................................ 58

System Preventive Maintenance Instructions

...................................................................................................... 67

System Components

 ........................................................................................................................................... 68

Recommended Spare Parts

 ................................................................................................................................ 69

Hardware Settings

 ............................................................................................................................................... 70

Control Rack Terminal Identification

 .................................................................................................................... 77

Serial Communication Protocols

 ......................................................................................................................... 81

Ratio Conversion

 ................................................................................................................................................. 81

MAINTENANCE:  

58-81

APPENDIX:  

82-94

Addendum A

 ........................................................................................................................................................ 82

Addendum B

 ........................................................................................................................................................ 84

Addendum C

........................................................................................................................................................ 85

Addendum D

........................................................................................................................................................ 86

Addendum E

 ........................................................................................................................................................ 94

MANUAL CHANGE SUMMARY:  

  95

Manual Changes

  .................................................................................................................................................95

PARTS IDENTIFICATION:  

47-57

4 Examples of Signal Sequencing

  ...................................................................................................................... 47

Procedures

 .......................................................................................................................................................... 51

PID Control

 .......................................................................................................................................................... 53

CONTENTS

LN-9400-00-R11  (08/2018)

3 / 96

www.carlisleft.com

CONTENTS

Содержание Ransburg DynaFlow 77376

































































































Отзывы:

Нет отзывов