Carlisle Ransburg DynaFlow 77376 Скачать руководство пользователя страница 17

Страница: 17 / 96

INSTALLATION

SYSTEM GUIDELINES

Prints Specific Per Installation

Often times, installation prints are custom drawn for each

site. You should check those prints for information that

is specific to your installation. Any deviations from those

prints made during or after installation should be recorded

for further reference.

Cable Assemblies

Most electrical interconnections between the DynaFlow

controller and other system components are made through

cable assemblies.

Equipment Locations

With the exception of the following restrictions, the

installation of the Transducers or Transducer Panel, the

Remote Operators Station and Regulator/Flow meter

assemblies are application and site dependant. Specific

instructions for location and mounting of these assemblies

are covered on the site installation drawings.

Equipment Grounding

1. The maximum recommended distance from the Control

Panel to each flow meter is 100-ft. as determined by the

maximum standard available length of the fiber-optic

cable assemblies or intrinsic electrical cable assemblies.

2. The maximum recommended length of air pilot tubing

between the electrical-to-pneumatic (E/P) transducer

and the material regulator is largely determined by the

application. In general, the pilot lines should be kept as

short as possible to achieve the best fluid flow response

and regulation. See "Pilot Signal Guidelines" chart in

this section.

3. The maximum distance between the optional LBAL5001-

XX Pneumatic Interface Panel to the Control Console

is 40-ft., as determined by the interconnecting electrical

cable assembly.

4. The maximum recommended 1/4-inch OD hose length

from the LBAL5003, Remote Operator Panel, and the

LBAL5001, Pneumatic Interface Panel, is 20-ft., however

this can be longer depending on the application. The

maximum distance between the A12182 interface panel

and the A12233 console is 50-ft.

5. The maximum recommended length for the E/P

transducer electrical control cable is 95 ft. However, in

some cases 175-ft. has been used. Generally, if a GUN

number (not atomizers) controls a complete zone of 6

or more atomizers, do not exceed 95-ft. of cable.

Consult Ransburg if longer distances than those shown

above are desired.

CAUTION

NOTE

Any unused conduit holes must be blanked off

to prevent solid objects from entering the interior of

the enclosure.

The control panel should be grounded in

accordance with national and local electrical codes.

The protective ground conductor must be

terminated directly to the protective conductor ground

terminal located inside the Control Enclosure which is

marked with symbol -

Return To Contents

LN-9400-00-R11 (08/2018)

17 / 96

www.carlisleft.com

INSTALLATION

Содержание Ransburg DynaFlow 77376

































































































Результаты поиска

Содержание Ransburg DynaFlow 77376

Отзывы:

Carlisle Ransburg DynaFlow 77376, Руководство по обслуживанию, Страница: 17 / 96

Результаты поиска

Содержание Ransburg DynaFlow 77376

Отзывы: