manualshive.com logo in svg

Carlisle Ransburg DynaFlow 77376, Руководство по обслуживанию, Страница: 69 / 96

Поделиться
Скачать
Carlisle Ransburg DynaFlow 77376 Скачать руководство пользователя страница 69

Part #

Notes

SPARE PARTS FOR DYNAFLOW RACK COMPONENTS

Description

77377-02
77378-00

DynaFlow Interface Module
DynaFlow Mother Board

77377-02 RIO Compatible

Total # of Interface Modules in System

1-4

4-10

>10

1
0

2
1

3
1

A10946-01/-02 DynaFlow Channel Module

1

2

3

Part #

Notes

Description

Total # of Channel Cards in System

>16

1-8

9-16

Part #

Notes

Description

Total # of Consoles

1-2

3-4

5+

77377-12 

DynaFlow Interface Module 

1 

2 

2 

A10946-01/-02  DynaFlow Channel Module 

1 

2 

3 

77378-00 

Mother Board 

0 

0 

1

 A11224-00 

Power Supply Assy., 24 VDC 

1 

1 

1 

73837-08 

Intrinsic Safety Barrier 

1 

1 

2 

For 77376-XXX1X Only

77454-00 or 

Fiber-Optic Flow Meter Receiver 

1 

1 

2 

For 77376-XXX0X Only

A12720-00
77382-00 

Ribbon Cable Adaptor 

0 

1 

1 

74300-00 

Bulb, 130 VAC 

1 

2 

2 

4131- 11 

Fuse, 3 AG, 3 AMP 

1 

2 

2 

77384-00 

Stop Switch, Red Mushroom Head 

1 

1 

1 

Included with all stand-alone systems

A11375-00 

Stop Switch, Yellow Mushroom Head 

1 

1 

1 

Alternate stop switch, available 

 

 

 

 

 

special order only, for integrated 

 

 

 

 

 

systems when only one red stop 

 

 

 

 

 

switch is permitted in the control 

 

 

 

 

 

room area. 

A10577-00 

Power Line Filter (115 VAC) 

1 

1 

1 

For 77376-XXXX0 Only

A10577-01 

Power Line Filter (230 VAC) 

1 

1 

1 

For 77376-XXXX0 Only

SPARE PARTS FOR 77376 AND A12233 CONSOLE UNIT

The following DynaFlow recommended spare parts lists

 

do not

 include auxiliary fluid control/monitoring equipment 

such as pneumatic interface panels, fluid panels, trans-

ducer panels, etc. The recommended spare parts list for 

the auxiliary equipment should be derived from previous 

fluid control lists since their usage and requirements are 

the same.

Recommended spare parts list for the DynaFlow rack 

components only.

Return To Contents

LN-9400-00-R11  (08/2018)

69 / 96

www.carlisleft.com

MAINTENANCE

Содержание Ransburg DynaFlow 77376

































































































Отзывы:

Нет отзывов