Carlisle Ransburg DynaFlow 77376 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 96

Carlisle Ransburg DynaFlow 77376 Скачать руководство пользователя страница 59

Displayed Text

Fault Cause

Corrective Action

ERROR CODES

(Cont.)

Code

TROUBLESHOOTING GUIDE

(Cont.)

(Continued On Next Page)

Reverse Flow Limit -
CHANNEL #<>

The amount of reverse flow for the in-
dicated CHANNEL has ex-ceeded the
maximum allowable amount as defined
in the CHANNEL parameter set.

Last digit indicates

CHANNEL #

.

Check the following:

1. That the Reverse Flow value entered in the

JOB # is correct.

2. Flow meter fiber-optic cables are properly

connected and not reversed.

3.  Fluid pressures are properly set and stable.
4.  All check valves are operating correctly.
5.  All fluid lines filled and all valves open.
6.  Flow meter is operating properly.

9021
9022
9023
9024
9025
9026
9027
9028

9031
9032
9033
9034
9035
9036
9037
9038

Flow Too Low -
CHANNEL #<>

The flow rate for the indicated CHANNEL
# is too low. Based on the transducer
output. Not issued for a manual GUN,
master CHANNEL.

Last digit indicates

CHANNEL #

.

Check the following:

1. There is fluid in the fluid lines for the

indicated CHANNEL.

2. Fluid pressures are properly set and

stable.

3. The pilot air line to the fluid regulator is

not damaged or leaking.

4. Fluid viscosity is correct for the CHANNEL

pressure and pipe size.

5. The pressure transducer and regulator

are operating properly.

6. Transducer air supply is at least 90 psi.
7. Kp, Ki, and Kd Gains are set correctly

for the indicated CHANNEL.

9041
9042
9043
9044
9045
9046
9047
9048

Flow Too High

The flow rate for the indicated CHANNEL
# is too high. Based on the transducer
output. Not issued for a manual GUN,
master CHANNEL.

Last digit indicates

CHANNEL #

.

Check the following:

1. Fluid regulators - sticking or faulty.
2. Control parameters - gains possibly set

too high.

3. MVR low setting too high.

9071
9072
9073
9074
9075
9076
9077
9078

No Master Flow

Manual mode only. A trigger signal was
received and no fluid flow was detected
through the master chan-nel after the
Blowoff timer had elapsed (if used).

Check the following:

1. There is fluid in the fluid lines for the

indicated CHANNEL.

2. Fluid pressure is OK.
3. The flow meter, pressure trans-ducer,

and regulator are operating properly.

Return To Contents

LN-9400-00-R11 (08/2018)

59 / 96

www.carlisleft.com

MAINTENANCE

«
...
57
58
59
60
61
...
»

Содержание Ransburg DynaFlow 77376

































































































Отзывы:

Нет отзывов