manualshive.com logo in svg

Carlisle Ransburg DynaFlow 77376, Руководство по обслуживанию, Страница: 72 / 96

Поделиться
Скачать
Carlisle Ransburg DynaFlow 77376 Скачать руководство пользователя страница 72

Position

Description

Default Setting

4 / 8

OFF

Alternate PID Equation

The Alternate PID Equation should be used whenever the set point for the flow rate is 

dynamically changed during Run mode.

OFF =   The PID Proportional term is based on the error term, which is the difference 

between the desired flow rate (set point) and actual flow rate.  

ON =   The PID Proportional term is based on the setpoint.

1 / 5

Trigger Detection Method

This switch setting effects only GUNs configured as dual-component, Manual mode.

OFF = GUN trigger input signal required.

ON  =   GUN  trigger  input  signal  not  required.    Fluid  flow  through  Master  CHANNEL 

initiates PID on Slave CHANNEL.  Master CHANNEL flow rate is determined by 

a manual flow rate adjustment located on the GUN.

OFF

3 / 7

OFF

Lookup Table Enabled 

(This feature has been obsoleted in current revisions of the software.)

This switch setting applies only to single-component GUNS.

OFF =  The Lookup Table is updated while in Run mode, but it is not used to determine 

the flow rate set point when the GUN is triggered.

ON =   The Lookup Table is updated while in Run mode and is used to determine the 

flow rate set point when the GUN is triggered, or when the flow rate set point is 

changed by more than 10% of the range in flow rate (Maximum Flow Rate minus 

Minimum Flow Rate).  In addition, if the GUN has been placed in Transparent 

mode and a PLC or robot sends a flow rate set point via RIO or Analog Input, 

the value is assumed to be a flow rate, rather than a pressure value.

2 / 6

Analog Hold Mode

OFF =  When the GUN trigger is removed, the E/P transducer pressure immediately 

returns to MVR LOW.

ON =   If the Trigger OFF Delay is zero, when the GUN trigger is removed, the E/P 

transducer pressure immediately returns to MVR LOW.  If the Trigger OFF Delay 

is non-zero, the E/P transducer pressure remains at the last output value from 

the PID loop until the Trigger OFF Delay expires.

OFF

CHANNEL MODULE P/N:  77206-XX or A10946-XX

DIP SWITCH SW1 SETTINGS

Return To Contents

LN-9400-00-R11  (08/2018)

72 / 96

www.carlisleft.com

MAINTENANCE

Содержание Ransburg DynaFlow 77376

































































































Отзывы:

Нет отзывов