Canon ImageRunner iR8500 Series, Руководство по обслуживанию, Страница: 688 / 1122

Chapter 14
14-34
Unless you have registered 'system control group ID' and 'system control
ID No.', you will not be able to register cards for the device in the course
of Net Spot Accountant setup work.
12) Download the card ID.
Keep the machine in a standby state < and download the card ID to
be used from the NSA>
13) Check the count control particulars in user mode.
system control setup>group ID control>count control
See that only the downloaded ID data is shown.
14) Check to see that the operation is normal.
Make copies using a user card that has been registered using the NSA,
and check to see that the count of the card in question has been
incremented correctly.
14.7.6 Replacing the Main Controller PCB
0008-8453
iR7200
1) Make a backup of the data using the Service Support Tool.
2) Replace the main controller PCB.
3) Detach the following PCBs from the existing PCB, and mount it to
the new PCB:
- SD-RAM [1]
- BOOT-ROM [2]
- Counter memory PCB [3]
F-14-68
4) After assembling the machine, connect the power plug to the power
outlet, while holding down '2' and '8' keys on the keypad in the
control panel at the same time, turn on the main power switch.
5) Put the data back in.
14.7.7 When Replacing the Main Controller PCB
0009-1302
iR85+
If you are replacing the main controller PCB, be sure to transfer the
following components from the old to new PCB:
[1] BootROM
[2] HDD
[3] image memory (SDRAM)
[4] counter memory PCB
F-14-69
If the user uses NetSpot Accountant (NSA) in Combination with a
Card Reader
The SDRAM of the main controller retains card ID used by NSA. If you
have replaced the main controller, you will have to download the card
data from NSA once again to permit NSA to perform statistical
operations.
If you have formatted the HDD and downloaded the system software,
you will have to go through a specific set of steps:
1) Format the HDD.
2) Download the system software.
3) Make the following selections:
COPIER>FUNCTION>INSTALL>CARD.
4) Enter a card No.
Enter the first of the numbers that will be used for group control,
and press the OK key (e.g., if you are planning to use cards from
No. 1 thorough No. 100, enter '1').
5) turn off and then on the main power.
6) Check the count control mechanism in user mode.
system control setup>group ID control>count control
check to see as many as 'ID00000001 through ID00001000' have been
prepared.
7) Set the IP address in user mode.
system control setup>network setup>TCP/IP setup>IP address
Set 'IP address', 'gateway address', and 'sub net mask'.
8) Enter a number of your choice in user mode.
system administrator info setup>system control group ID>system
control ID No.
9) Hold down the control panel power switch for 3 sec or more.
10) Go through the instructions on the control panel for shut-down
sequence so that the main power switch may be turned off.
11) Turn off the main power switch. Wait for 3 sec or more, and turn it
back on.
Unless you have registered 'system control group ID' and 'system control
ID No.', you will not be able to register cards for the device in the course
of Net Spot Accountant setup work.
12) Download the card ID.
Keep the machine in a standby state < and download the card ID to
be used from the NSA>
13) Check the count control particulars in user mode.
system control setup>group ID control>count control
See that only the downloaded ID data is shown.
14) Check to see that the operation is normal.
Make prints using a user card that has been registered using the NSA,
and check to see that the count of the card in question has been
incremented correctly.
14.7.8 When Replacing the HV-DC PCB
0009-1597
/ iR85+ / iR8070
1) Replace the HV-DC PCB.
2) Assemble the machine; then, connect the power plug to the power
[1]
[2]
[3]
[1]
[2]
[3]
[4]