Canon imageRUNNER ADVANCE C2000 Series Скачать руководство пользователя страница 133

Страница: 133 / 175

e-Support

Filename:

TP13 031.pdf

Date:

01-28-13

Page 4 of 8

SERVICING:

Output a PG print by following the steps below and make a Service Mode adjustment of the toner color that
has the ghost image problem.

Change the setting value from "59" to "1000" in Service Mode > Mode List > COPIER > Adjust >
BLANK > BLANK-B.

Select a paper cassette from "A4" or "LTR" in Service Mode > Mode List > COPIER > Test > PG
>PG-PICK.

Change the setting value to "255" in Service Mode > Mode List > COPIER > Test > PG > DENS-
Y/M/C/K.

Change the setting value to "0" (Full Color Mode) in Service Mode> Mode List > COPIER > Test >
PG > F/

M-SW, set "49" in Service Mode > Mode List > COPIER > Test > PG > TYPE, and then output a
PG print.

Repeat the above procedure by changing the setting value to "1" (Black and White Mode) in Service
Mode > Mode List > COPIER > Test > PG > F/M-SW.

The following images are PG49 test prints when the ghost did not occur.

The sample [A] is an image printed in Full Color Mode, and the sample [B] in Black and White
Mode.

Содержание imageRUNNER ADVANCE C2000 Series
















































































































































































Результаты поиска

Содержание imageRUNNER ADVANCE C2000 Series

Отзывы:

Похожие инструкции для imageRUNNER ADVANCE C2000 Series

Бренды по названию

Популярные бренды

Canon imageRUNNER ADVANCE C2000 Series, Техническое пособие

Результаты поиска

Содержание imageRUNNER ADVANCE C2000 Series

Отзывы:

Похожие инструкции для imageRUNNER ADVANCE C2000 Series

Бренды по названию

Популярные бренды