CADDX RANGER 7600, Руководство по установке

Страница: 16 / 38

16
LOCATION 131: AUTOMATIC BYPASS / INSTANT ARMING
Location 131 is used to enable "Automatic Bypass/Instant Arming". Programming a "1" in this location will cause
the control to automatically enter the "Instant" mode and bypass interior follower zones if a fault is not detected on
an entry/exit zone during the exit delay. Programming a "3" in this location, will cause the interior follower zones to
become bypassed if a fault is not detected on an entry/exit zone, yet will not change the status of the entry/exit zone.
If this location contains a "0", these features are disabled. Pressing the [
r
] key when the system is armed, will cause
the "Instant" light to toggle. When the "Instant" light is on, the entry/exit zone is instant; when off, the entry/exit zone
is delayed. The [
r
] key will toggle the "Instant" mode regardless of the programming data in this location. When the
system is armed, bypassed interior follower zones can be reactivated by entering [first digit of master code] followed
by [
r
]. Once the interior is reactivated they cannot be bypassed again without disarming the control.
LOCATION 132: ENABLE KEYPAD SIREN SOUNDER
The built-in keypad siren of the 8001 is enabled in location 132 by programming a "1" in location 132 to enable.
LOCATION 133: L.E.D. EXTINGUISH FEATURE
Keypad LEDs (with the exception of the A.C. LED) will be extinguished after 60 seconds of keypad inactivity if a "1"
is programmed in location 133. The LEDs will become illuminated immediately upon a keypress or alarm condition.
LOCATION 134: ENTERING THE NUMBER OF DIAL ATTEMPTS
Location 134 is used to enter the number of dial attempts (1 to 15 attempts) the communicator will try for the
appropriate phone number(s) before ending the notification process. If this location contains an "8", the
communicator will make 8 attempts to the first number, and then eight attempts to a second number, if a second
number is programmed as backup.
LOCATION 135: POWER UP CONDITION
If a "1" is programmed in location 135, the Ranger 7600 will power-up disarmed if there is a total power shutdown
and battery failure. If a "2" is programmed in this location, it will power up armed. If this location contains a "0", the
Ranger 7600 will maintain the condition it was in at power down. A watchdog circuit reset will cause the Ranger 7600
to reset to the selected condition.
LOCATION 136: POWER UP DELAY
If a "1" is programmed in location 136, the Ranger 7600 will not delay 60 seconds before accepting open or short
inputs from any zone. If a "0" is programmed, sensors on all zones are allowed 60 seconds to stabilize at power-up,
or after exiting the program mode. After 60 seconds, the Ranger will once again accept loop opens or shorts as an
alarm condition. This 60 second period will also be initiated after a watchdog circuit reset condition.
LOCATION 137: IMMEDIATE RESTORE BY ZONE
If a "1" is programmed in location 137, restoral signals will follow the restore condition and report restores
immediately after the condition has unfaulted. A non-extended format will not send a restore message until all zones
and trouble conditions have restored. If this location contains a "0", the restore signal or signals will be reported only
after siren timeout.
LOCATION 138: NO ARMING WITH A ZONE BYPASSED
If a "1" is programmed in location 138, the Ranger 7600 will not arm with any zone bypassed.
LOCATION 139: ENABLING QUICK ARM
The Ranger 7600 can be programmed to "Quick Arm" with the 3 key by programming a "1" in location 139. A "0" in
this location will disable this feature. If the "Quick Arm" digit is the same as the first digit of the "Go To Program
Code", the "Quick Arm" code will not function.