Bosch Rexroth HMU05.1N Series Скачать руководство пользователя

Страница: 67 / 410

Application

Air-

liquid

cooling unit

Particularly suited for individual workshop machines.
Is used
●

Where there is no higher-level cooling circuit available

●

Where there are no high demands on the stability of the cool‐

ant temperature

liquid
liquid

cooling unit

Particularly suited for systems with central recooling.
Is used where there are no high demands on the stability of the

coolant temperature.

Refrigerating

unit

Particularly suited where a high degree of thermal stability in a sys‐

tem is required.
A certain temperature is kept constant, the temperature increase

from electrical components therefore does not have any effect on

the precision of the system.

Tab. 4-9:

Uses of cooling devices

Cost comparison

Air-liquid cooling unit

Liquid-liquid cooling unit

Refrigerating unit

Fig. 4-10:

Approximate cost comparison of the cooling devices

Cooling device components
Overview

A liquid cooling system consists of:
●

A cooling device and

●

The drive components being cooled, including
–

Lines

–

Fittings

–

Shut-off devices, etc.

Heat is dissipated by a heat exchanger to a higher-level cooling medium.

DOK-INDRV*-HXX05******-PR02-EN-P

Bosch Rexroth AG

65/407

Rexroth IndraDrive ML Drive Systems with HMU05

Combining the individual components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды