Bosch Rexroth HMU05.1N Series Скачать руководство пользователя страница 322

Страница: 322 / 410

Disconnect the hosing (E).

Disconnect the hosing (F).

Remove the cover (G).

Disconnect the cables from the ter‐

minals.

Unscrew the screws (H).

10 Remove the pump.
11 Install the new pump.

To fit the new pump carry out the

removal operations described in re‐

verse order.

12 Fill the drive circuit (see see

chap‐

ter "Procedure to fill the drive cir‐

cuit" on page 310

Tab. 8-111:

Replacing the main pump

Replacing the mixing valve

Unscrew the collars (A).

Remove the valve (B) and the ac‐

tuator (C).

Remove the gaskets (D).

Unscrew the screws (E).

Separate the valve from the actua‐

tor.

Join the new valve to the actuator.

Position the gaskets (D).
Replace the gaskets if damaged or

worn.

Place the valve and actuator in

their position.

Screw in the collars (A).
To fit the new valve carry out the

removal operations described in re‐

verse order.

Tab. 8-112:

Replacing the mixing valve

Bosch Rexroth AG

DOK-INDRV*-HXX05******-PR02-EN-P

320/407

Rexroth IndraDrive ML Drive Systems with HMU05

Cables, accessories, additional components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды