Bosch Rexroth HMU05.1N Series Скачать руководство пользователя страница 77

Страница: 77 / 410

The following properties of series connection generally have to be observed:
●

Series connection does not allow setting the required flow rate individu‐

ally for each of the connected components.

●

The required system pressure corresponds to the sum of all pressure

decreases of the connected individual components. This means a lower

degree of hydraulic operational safety of due to high system pressure.

●

The temperature level of the coolant increases from component to com‐

ponent because each power dissipation discharged to the coolant in‐

creases its temperature. This means uneven machine temperature in‐

crease by the components being cooled.

Combined interconnection

Fig. 4-33:

Combined interconnection of drive components being cooled

The combined interconnection of the drive components being cooled allows

using the advantages of parallel and series connection.

Condensation protection

Risk of damage. Drive components cannot

build condensation.

NOTICE

In temperate zones (up to 40°C and 70% humidity), the inlet temperature of

the coolant may be at a maximum 5 K below the temperature in the control

cabinet.
Safest protection against condensation:
Coolant inlet temperature = ambient temperature

The temperature of the coolant flowing through liquid-cooled drive compo‐

nents generally differs from the temperature of the ambient air.
Depending on the humidity, the ambient air contains water vapor. The

amount of water vapor which can be absorbed by the air depends on the air

temperature and air pressure. The warmer the air, the more water vapor it

can absorb at the same air pressure.
When warm air gets in contact with a less warm object, a moist film (conden‐

sation) forms on the surface of the object if the temperature of the object is

below the condensation temperature.
Drive components with protection classes IPx4, IPx5, IPx6 are not at risk

from condensation because their design provides sufficient protection against

water.

DOK-INDRV*-HXX05******-PR02-EN-P

Bosch Rexroth AG

75/407

Rexroth IndraDrive ML Drive Systems with HMU05

Combining the individual components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды