Bosch Rexroth HMU05.1N Series Скачать руководство пользователя

Страница: 43 / 410

minutes! The time required for cooling down is approximately five times

the thermal time constant specified in the technical data.

●

Before touching chokes after having switched them off, let them cool

down for a sufficient period of time. Cooling down can require up to 140

minutes!

●

After switching off supply units and drive controllers, wait 15 minutes to

allow them to cool down before touching them.

●

Wear safety gloves or do not work at hot surfaces.

●

For certain applications, and in accordance with the respective safety

regulations, the manufacturer of the machine or installation must take

measures to avoid injuries caused by burns in the final application.

These measures can be, for example: Warnings at the machine or in‐

stallation, guards (shieldings or barriers) or safety instructions in the ap‐

plication documentation.

3.3.6

Protection during handling and mounting

Risk of injury by improper handling! Injury by crushing, shearing, cutting, hit‐

ting!
●

Observe the relevant statutory regulations of accident prevention.

●

Use suitable equipment for mounting and transport.

●

Avoid jamming and crushing by appropriate measures.

●

Always use suitable tools. Use special tools if specified.

●

Use lifting equipment and tools in the correct manner.

●

Use suitable protective equipment (hard hat, safety goggles, safety

shoes, safety gloves, for example).

●

Do not stand under hanging loads.

●

Immediately clean up any spilled liquids from the floor due to the risk of

falling!

3.3.7

Battery safety

Batteries consist of active chemicals in a solid housing. Therefore, improper

handling can cause injury or property damage.
Risk of injury by improper handling!
●

Do not attempt to reactivate low batteries by heating or other methods

(risk of explosion and cauterization).

●

Do not attempt to recharge the batteries as this may cause leakage or

explosion.

●

Do not throw batteries into open flames.

●

Do not dismantle batteries.

●

When replacing the battery/batteries, do not damage the electrical parts

installed in the devices.

●

Only use the battery types specified for the product.

DOK-INDRV*-HXX05******-PR02-EN-P

Bosch Rexroth AG

41/407

Rexroth IndraDrive ML Drive Systems with HMU05

Safety instructions for electric drives and controls

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды