Bosch Rexroth HMU05.1N Series Скачать руководство пользователя страница 121

Страница: 121 / 410

Condition as supplied, identification, transport and

storage

5.1

Condition as supplied

5.1.1

Factory testing

Voltage testing and insulation resistance testing

According to standard, the components of the Rexroth IndraDrive ML range

are tested with voltage.

Testing

Test rate

Voltage testing

100% (EN 61800-5-1)

Insulation resistance testing

100% (EN 60204-1)

Tab. 5-1:

Applied standards

5.1.2

Customer testing

Risk of damage to the installed Rexroth com‐

ponents by customer-side testing of the ma‐

chine or installation!

NOTICE

Before conducting voltage testing or insulation resistance testing for an instal‐

lation or machine in which these components are used:
Disconnect all connections to the Rexroth components or disconnect the

plug-in connections to protect the electronic components.

DOK-INDRV*-HXX05******-PR02-EN-P

Bosch Rexroth AG

119/407

Rexroth IndraDrive ML Drive Systems with HMU05

Condition as supplied, identification, transport and storage

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды