Bosch Rexroth HMU05.1N Series страница 300 Скачать руководство пользователя

Страница: 300 / 410

Processing and protection devices

Serious health and safety risks

WARNING

Do not tamper with, circumvent, remove or bypass processing and protection

devices; failure to comply with this requirement may cause serious health and

safety risks.

Pressure switch (0,5 bar): this detects the pres‐

sure level in the intake manifold.
The pressure switch allows a warning to be sig‐

nalled when the pressure falls below 0,5 bar.

Pressure switch (0,2 bar): this detects the pres‐

sure level in the intake manifold.
The pressure switch allows an "error" to be sig‐

nalled when the pressure falls below 0,2 bar

and stops machine operation.

Bypass valve: this is used to keep the fluid pres‐

sure in the drive circuit outlet pipe within the

maximum limit allowed.

Temperature sensor: this detects the coolant

temperature in the drive circuit outlet pipe.
Depending on the temperature detected, the

system will signal either a "Warning"(tempera‐

ture too high) or an "Error" (temperature contin‐

ues to rise, resulting in machine shutdown).

Pressure sensor: this detects, in real time, the

differential pressure between the intake pipe

and the drive circuit output pipe.
Through the sensor, the drive circuit outlet pipe

pressure is kept constant.

Check valve: this is used to stop the filling pump

intake pipe draining.

Tab. 8-94:

Processing and protection devices

Environmental conditions for operation

The machine works correctly with an ambient temperature of between 5 and

55 °C and a maximum humidity level of 95% (without condensation).
The machine is able to function properly at altitudes up to 2000 m above sea

level.

Permitted use

The machine is designed and manufactured to cool electric or electronic

equipment or machines.
Any other use than that specified, or not included or inferable from this man‐

ual, should be considered mishandling and therefore not permitted.

Improper and unauthorised uses

It is forbidden to use coolants with characteristics different from those speci‐

fied by the manufacturer.

Bosch Rexroth AG

DOK-INDRV*-HXX05******-PR02-EN-P

298/407

Rexroth IndraDrive ML Drive Systems with HMU05

Cables, accessories, additional components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды