Bosch Rexroth HMU05.1N Series Скачать руководство пользователя страница 294

Страница: 294 / 410

Heat exchanger: it lowers the temperature of the coolant in the

drive circuit

Expansion tank: it maintains the pressure in the drive circuit

constant

Coolant distribution manifold

Valve: this is used to open and close the flow from the filling

pump

Valve: this is used to open and close the flow of the main pump

Main pump: it makes the coolant circulate in the drive circuit

Filling pump: it fills the cooling circuit of the owner’s equipment

By-pass valve: it limits the pressure of the output liquid

Pressure sensor: this measures the differential pressure be‐

tween the intake and the outlet of the machine to be cooled

Check valve: this is used to stop the filling pump intake pipe

draining

Fig. 8-78:

Operational cycle and component description

Guards

The owner must fit the machine with suitable guards in conformity with the

regulations in force, in order to prevent the risk of injury.

Overpressure devices

The owner is obliged to install a safety device in the drive circuit, on the re‐

turn pipe to the machine, which limits the pressure in the system to a maxi‐

mum of 2 bar.

Bosch Rexroth AG

DOK-INDRV*-HXX05******-PR02-EN-P

292/407

Rexroth IndraDrive ML Drive Systems with HMU05

Cables, accessories, additional components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды