Bosch Rexroth HMU05.1N Series страница 117 Скачать руководство пользователя

Страница: 117 / 410

Clock frequency Parallel HMU05s can only be operated at clock frequencies

below 8 kHz.

Motor

A motor can be operated with electrically isolated windings.

A motor cannot be operated with phase-shifted windings.

Fig. 4-58:

Parallel operation of HMU05 to run as drive controller

When running in parallel, one HMU05 is the "master" and the other HMU05s

are the "slaves".
The master has a CSx02.5 control section and an HPC01.1-MN02 optional

card. The master communicates with the slaves through the HPC01.1-P001

optional cards (ring topology). Connection cables to the HPC01.1-P001 op‐

tional cards always have to be run inside the control cabinet. Comply with

maximum allowed line lengths.
The power outputs have to be wired symmetrically to ensure the output cur‐

rent of the HMU05s are symmetrically distributed and no HMU05s are over‐

loaded. To do this, the power outputs are connected to a common busbar.

The motor is then connected directly to the busbar.

Maximum line lengths

Between HMU05 and motor:
●

Shielded: 100 m

●

Unshielded: 150 m

DOK-INDRV*-HXX05******-PR02-EN-P

Bosch Rexroth AG

115/407

Rexroth IndraDrive ML Drive Systems with HMU05

Combining the individual components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды