manualshive.com logo in svg

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Поделиться
Скачать
Bosch Rexroth HMU05.1N Series Скачать руководство пользователя страница 361

5

Undo the screw and remove the

strap (D).

6

Disconnect the hosing (E).

7

Repeat the same operations to re‐

move the other flexible tube.

8

Remove the cover (F).

9

Disconnect the cables from the ter‐

minals.

10 Unscrew the screws (G).
11 Remove the pump.
12 Install the new pump.

To fit the new pump carry out the

removal operations described in re‐

verse order.
NOTICE! The spare pump is sup‐

plied with the fittings mounted.
Do not unscrew the fittings as this

could cause liquid leakage.

Tab. 8-132:

Replacing the main pump

DOK-INDRV*-HXX05******-PR02-EN-P 

Bosch Rexroth AG

359/407

Rexroth IndraDrive ML Drive Systems with HMU05

Cables, accessories, additional components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды