manualshive.com logo in svg

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Поделиться
Скачать
Bosch Rexroth HMU05.1N Series Скачать руководство пользователя страница 354

Procedure to empty the hydraulic circuit

Fig. 8-90:

Procedure to empty the hydraulic circuit

1. Position a suitable container in which to collect the coolant.
2. Stop the machine (see 

chapter "Stopping procedure" on page 348

).

3. Turn the key selector (C) to "OFF" position.
4. Turn the main cut-off switch (A) to the "OFF" position.
5. The signal light (B) will switch off.
6. Close the ball valves (F - G).
7. Open the valve (H).
8. Unscrew caps (L).
9. Drain out all the coolant.

10. Close the valve (H).
11. Screw on the caps (L).

 
NOTICE! Do not dump the coolant; dispose of it in accordance with the

laws in force.

Bosch Rexroth AG

 DOK-INDRV*-HXX05******-PR02-EN-P

352/407

Rexroth IndraDrive ML Drive Systems with HMU05

Cables, accessories, additional components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды