manualshive.com logo in svg

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Поделиться
Скачать
Bosch Rexroth HMU05.1N Series Скачать руководство пользователя страница 349

Starting procedure

At first start-up, carry out the circuit filling procedure (see 

chapter "Procedure

to fill the hydraulic circuit" on page 349

).

To start the machine, proceed as described.

1

Open the ball valves (F - G).

2

Turn the main cut-off switch (A) to the "ON" po‐

sition.
The indicator lamp (B) lights up.

3

Turn the key selector (C) to "automatic" posi‐

tion.
Machine start-up must be performed using the

operating terminal of the machine to be cooled,

via the "ENABLE" connection (see 

chapter

"ENABLE, UNIT ERROR and UNIT WARNING

connections" on page 334

).

Tab. 8-126:

Starting procedure

DOK-INDRV*-HXX05******-PR02-EN-P 

Bosch Rexroth AG

347/407

Rexroth IndraDrive ML Drive Systems with HMU05

Cables, accessories, additional components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды