Bosch Rexroth HMU05.1N Series страница 44 Скачать руководство пользователя

Страница: 44 / 410

Environmental protection and disposal! The batteries contained in

the product are considered dangerous goods during land, air, and

sea transport (risk of explosion) in the sense of the legal regula‐

tions. Dispose of used batteries separately from other waste. Ob‐

serve the national regulations of your country.

3.3.8

Protection against pressurized systems

According to the information given in the Project Planning Manuals, motors

and components cooled with liquids and compressed air can be partially sup‐

plied with externally fed, pressurized media, such as compressed air, hy‐

draulics oil, cooling liquids and cooling lubricants. Improper handling of the

connected supply systems, supply lines or connections can cause injuries or

property damage.
Risk of injury by improper handling of pressurized lines!
●

Do not attempt to disconnect, open or cut pressurized lines (risk of ex‐

plosion).

●

Observe the respective manufacturer's operating instructions.

●

Before dismounting lines, relieve pressure and empty medium.

●

Use suitable protective equipment (safety goggles, safety shoes, safety

gloves, for example).

●

Immediately clean up any spilled liquids from the floor due to the risk of

falling!

Environmental protection and disposal! The agents (e.g., fluids)

used to operate the product might not be environmentally friendly.

Dispose of agents harmful to the environment separately from

other waste. Observe the national regulations of your country.

3.4

Explanation of signal words and the Safety alert symbol

The Safety Instructions in the available application documentation contain

specific signal words (DANGER, WARNING, CAUTION or NOTICE) and,

where required, a safety alert symbol (in accordance with

ANSI Z535.6-2011).
The signal word is meant to draw the reader's attention to the safety instruc‐

tion and identifies the hazard severity.
The safety alert symbol (a triangle with an exclamation point), which pre‐

cedes the signal words DANGER, WARNING and CAUTION, is used to alert

the reader to personal injury hazards.

DANGER

In case of non-compliance with this safety instruction, death or serious injury

will occur.

Bosch Rexroth AG

DOK-INDRV*-HXX05******-PR02-EN-P

42/407

Rexroth IndraDrive ML Drive Systems with HMU05

Safety instructions for electric drives and controls

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды