Bosch Rexroth HMU05.1N Series страница 338 Скачать руководство пользователя

Страница: 338 / 410

Processing and protection devices

Serious health and safety risks!

WARNING

Do not tamper with, circumvent, remove or bypass processing and protection

devices; failure to comply with this requirement may cause serious health and

safety risks.

Pressure switch (0,5 bar): this detects the

pressure level in the intake manifold.
The pressure switch allows a "Warning"

to be signalled when the pressure falls

below 0,5 bar.

Pressure switch (0,2 bar): this detects the

pressure level in the intake manifold.
The pressure switch allows an "Error" to

be signalled when the pressure falls be‐

low 0,2 bar and stops machine operation.

Bypass valve: this is used to keep the flu‐

id pressure in the outlet pipe within the

maximum limit allowed.

Temperature sensor: this detects the

coolant temperature in the outlet pipe.
Depending on the temperature detected,

the system will signal either a "Warn‐

ing"(temperature too high) or an "Error"

(temperature continues to rise, resulting

in machine shutdown).

Pressure sensor: this detects, in real

time, the differential pressure between

the intake pipe and the output pipe.
Through the sensor, the outlet pipe pres‐

sure is kept constant.

Check valve: this is used to stop the filling

pump intake pipe draining.

Tab. 8-119:

Processing and protection devices

Environmental conditions for operation

The machine works correctly with an ambient temperature of between -20

and 40 °C and a maximum humidity level of 95% (without condensation).
The machine is able to function properly at altitudes up to 2000 m above sea

level.

Permitted use

The machine is designed and manufactured to cool electric or electronic

equipment or machines.
The machine must be used in conformity with its technical characteristics; it is

forbidden to make modifications or use the machine for improper uses.
The machine can be used either indoors or outdoors, in areas exposed to the

weather.

Bosch Rexroth AG

DOK-INDRV*-HXX05******-PR02-EN-P

336/407

Rexroth IndraDrive ML Drive Systems with HMU05

Cables, accessories, additional components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды