Bosch Rexroth HMU05.1N Series Скачать руководство пользователя страница 312

Страница: 312 / 410

Procedure to fill the drive circuit

Check that the installation, electrical connections and hydraulic connections

are made to a professional standard in accordance with the manufacturer’s

instructions.

Fill a tank with an appropriate

amount of fluid solution (see

chapter "Specifications" on

page 294

Fit the pipes (L - M) into the

tank.

Open the ball valve (A).

Open the ball valve (B).

Open the valve (C).

Open the valve (D).

Open the valve (E).

Turn the key-operated selec‐

tor switch (F) to "service" to

prevent unexpected activa‐

tion of the main pump.

Make sure that the remote-

controlled "ENABLE" function

is activated.

10 NOTICE! Do not turn the se‐

lector switch (F) to "automat‐

ic" as this could cause dam‐

age to the main pump.

Open any of the valves in‐

stalled outside the machine

on the circuit for the machine

to be cooled.

11 Turn the main cut-off switch (G) to the "ON" position.

The indicator lamp (P) lights up.

12 Turn the selector switch (H) to activate the filling pump.

Always keep the fluid in the tank at a sufficient level.

13 Close the valve (D) when the fluid is running out of the clear tube (L) in a steady stream (no bubbles) and the pres‐

sure has reached 1,5 bar.
The pressure is shown by the pressure gauge (N).

14 Open the valve (D).
15 Turn the key-operated selector switch (F) to "automatic" to activate the main pump.

Bosch Rexroth AG

DOK-INDRV*-HXX05******-PR02-EN-P

310/407

Rexroth IndraDrive ML Drive Systems with HMU05

Cables, accessories, additional components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Бренды по названию

Популярные бренды