Bosch Rexroth HMU05.1N Series страница 182 Скачать руководство пользователя

Страница: 182 / 410

XG33, on, off, ZKS (DC bus short circuit) status

View

Connec‐

tion

I/O

Function

Supply voltage of inputs/outputs (24VEA*)

Supply voltage for external, current sourcing output

(ZKS1*)
Output (24VEA) is used to connect input XG33.3

DC bus short-circuit input for signaling an active DC

bus short circuit (ZKS2*)
Not connected:
ZKS active
Connected to 24VEA of XG33.2:
ZKS not active
The mains contactor opens in the case of an active

DC bus short circuit.

Supply voltage for external OFF output (OFF1*)
Output (24VEA) is used to connect input XG33.5

OFF input (OFF2*)
Connection for N/C contact to switch off the supply

unit
The input is always available, irrespective of wheth‐

er or not a master communication has been activa‐

ted. Compared to the master communication, the

input is of higher priority. The input can be used, for

example, to loop in an emergency stop circuit or the

like.

Supply voltage for external ON output (ON1*)
Output (24VEA) is used to connect input XG33.7

ON input (ON2*)
Connection for N/O contact to switch on the supply

unit.
The input is edge-controlled.
The input is only available, if the master communi‐

cation has been deactivated (P-0-4089.0.1).

Reference potential of supply voltage (0VEA*)

Description in connection diagram (see

chapter 4.6.2 "Overall

connection diagram (HMU05 as supply unit)" on page 95

)

Tab. 8-25:

Function, pin assignment

Operating HNA05 with HMU05 (slave mode) requires at least the

OFF input and the DC bus short circuit input (ZKS) to be connec‐

ted.

Bosch Rexroth AG

DOK-INDRV*-HXX05******-PR02-EN-P

180/407

Rexroth IndraDrive ML Drive Systems with HMU05

Cables, accessories, additional components

Содержание Rexroth HMU05.1N Series



























































































































































































































































































































































































































Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды

Bosch Rexroth HMU05.1N Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth HMU05.1N Series

Отзывы:

Похожие инструкции для Rexroth HMU05.1N Series

Бренды по названию

Популярные бренды