Blueprint Subsea seatrac X100 Series страница 88 Скачать руководство пользователя | Manualshive

Страница: 88 / 140

background image

SeaTrac Serial Command Interface Reference

Page 88

7.5.

Calibration Messages

Occasionally the beacon will need its onboard sensor calibrating, specifically the magnetometer
(to provider the magnetic north yaw heading for the AHRS system), and the pressure-sensor
offset for the depth computation (to compensate for atmospheric pressure changes).

The following calibration commands have been provided to allow application and developers
easy access to sensor calibration functions.

7.5.1.

CID_CAL_ACTION

The Calibration Action command should be used at various times by external calibration
applications and algorithms to instruct to beacon to perform operations related to one of its
on-board sensors.

Command Message Parameters

Parameter Type Description

MSG_ID

identification code

(CID_AHRS_CAL_SET)

ACTION

The code of the calibration action that should be
performed. See below for further details of each
operation code.

Response Message Parameters

Parameter Type Description

MSG_ID

identification code

(CID_AHRS_CAL_SET)

STATUS

Status code used to indicate if the command
executed successfully.
Valid values are…



CST_OK – The command was performed
successfully.



CST_CMD_PARAM_MISSING – The
ACTION parameter was not specified
correctly.

Summary of Calibration Actions…



CAL_ACC_DEFAULTS

This operation sets the current accelerometer calibration
coefficients back to their values (of 0) in the AHRS
working

settings.

However, this does not reset the currently measured
sensor limit values (output in the

message),

that are used to determine the calibration coefficients by

«
...
86
87
88
89
90
...
»

Содержание seatrac X100 Series













































































































































Отзывы:

Нет отзывов

Похожие инструкции для seatrac X100 Series

Бренд: Saab Страницы: 4

Бренд: Hytera Страницы: 11

Бренд: XHDATA Страницы: 4

Бренд: Radio Shack Страницы: 1

Бренд: Konig Страницы: 21

Бренд: LST Страницы: 3

Бренд: Salora Страницы: 17

Бренд: S&C Страницы: 14

Бренд: Sangean Страницы: 116

Бренд: SOUNDMASTER Страницы: 15

Бренд: QFX Страницы: 6

Бренд: Narex Страницы: 40

Бренд: JRC Страницы: 4

Бренд: Vertex Standard Страницы: 5

Бренд: Midland Страницы: 40

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды