Blueprint Subsea seatrac X100 Series страница 135 Скачать руководство пользователя

Страница: 135 / 140

SeaTrac Serial Command Interface Reference

Page 135

8.5.

DEX Protocol Messages

The Data Exchange protocol build on the simple data transfer functions provided by the DAT
protocol to provide additional features including…



Bi-directional data transfer within a single request-response message exchange



Port numbers to allow the creation and decoding of data streams



Buffered sockets, allowing links to be defined between beacon pairs, and data placed
onto the appropriate buffer ready for transfer.



Synchronised retry mechanism, to track which data has been sent and which packets
have failed and need to be resent.

This section is still under construction and will be detailed in the next release of this document.

8.5.1.

CID_DEX_CLOSE

8.5.2.

CID_DEX_DEBUG

8.5.3.

CID_DEX_ENQUEUE

8.5.4.

CID_DEX_OPEN

8.5.5.

CID_DEX_RESET

8.5.6.

CID_DEX_SEND

8.5.7.

CID_DEX_SOCKETS

8.5.8.

CID_DEX_RECEIVE

Содержание seatrac X100 Series













































































































































Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды

Blueprint Subsea seatrac X100 Series, Руководство пользователя

Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды