Blueprint Subsea seatrac X100 Series страница 36 Скачать руководство пользователя | Manualshive

Страница: 36 / 140

background image

SeaTrac Serial Command Interface Reference

Page 36

6.3.6.

CID_E (Command Identification Codes)

Command Identification (CID) Codes are an enumeration (or defined set of constants)
stored/transmitted in a UINT8 type at the start of Command and Response messages after the
synchronisation character, with the purpose of identifying the message function and its
payload.

The usage of each CID, including definition of message fields for both Command and Response
payloads is discussed in section 7 from page 65.

Value Symbolic

Name

Summary

System Messages

0x01

CID_SYS_ALIVE

Command sent to receive a simple alive
message from the beacon.

0x02

CID_SYS_INFO

Command sent to receive hardware &
firmware identification information.

0x03

CID_SYS_REBOOT

Command sent to soft reboot the beacon.

0x04

CID_SYS_ENGINEERING

Command sent to perform engineering
actions.

Firmware Programming Messages

0x0D

CID_PROG_INIT Command

sent

to initialise a firmware

programming sequence.

0x0E

CID_PROG_BLOCK

Command sent to transfer a firmware
programming block.

0x0F

CID_PROG_UPDATE

Command sent to update the firmware once
program transfer has completed.

Status Messages

0x10

CID_STATUS

Command sent to request the current system
status (AHRS, Depth, Temp, etc).

0x11

CID_STATUS_CFG_GET Command sent to retrieve the configuration of

the status system (message content and
auto-output interval).

0x12

CID_STATUS_CFG_SET

Command sent to set the configuration of the
status system (message content and auto-
output interval).

«
...
34
35
36
37
38
...
»

Содержание seatrac X100 Series













































































































































Отзывы:

Нет отзывов

Похожие инструкции для seatrac X100 Series

Бренд: Harken Страницы: 4

Бренд: E-Bench Страницы: 49

Badradio SR-300

Бренд: Hama Страницы: 3

Бренд: Xoro Страницы: 16

Бренд: i-box Страницы: 18

Бренд: Star Страницы: 16

Бренд: ConcealFab Страницы: 22

Бренд: EGG Страницы: 52

Бренд: JRC Страницы: 8

Бренд: perfect pro Страницы: 116

Бренд: Vetus Страницы: 44

Бренд: RTS Страницы: 40

Бренд: Attwood Страницы: 1

Бренд: Radio Shack Страницы: 20

Бренд: Ocean Digital Страницы: 2

Бренд: Bush Страницы: 25

Бренд: System Sensor Страницы: 4

Бренд: Kirisun Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды