Blueprint Subsea seatrac X100 Series страница 65 Скачать руководство пользователя | Manualshive

Страница: 65 / 140

background image

SeaTrac Serial Command Interface Reference

Page 65

7.

Beacon Management Message Definitions

7.1.

System Messages

System messages are the core set of command supported by the beacon in both its normal
operating mode and in Bootloader mode.
These commands provide basic functions to determine if the device is response, identify its
hardware/firmware configuration, and allow firmware reprogramming.

7.1.1.

CID_SYS_ALIVE

The CID_SYS_ALIVE command is a simple command that can be periodically sent to the
beacon to determine if the hardware is present, connected and functioning.
For example, a host system sending the CID_SYS_ALIVE command at regular intervals can use
the response reply to reset a “connection lost” timeout timer, so that when a connection fails
the lack of responses can indicate to the user the hardware is no longer present.

Command Message Parameters

Parameter Type Description

MSG_ID

Command

identification code (CID_SYS_ALIVE)

Response Message Parameters

Parameter Type Description

MSG_ID

Command

identification code (CID_SYS_ALIVE)

SECONDS

UINT32

The number of seconds the beacon has been
powered up for.

«
...
63
64
65
66
67
...
»

Содержание seatrac X100 Series













































































































































Отзывы:

Нет отзывов

Похожие инструкции для seatrac X100 Series

Бренд: Makita Страницы: 12

Бренд: Team Страницы: 33

Бренд: Uniden Страницы: 42

Бренд: HanRongDa Страницы: 16

Бренд: Sandstrom Страницы: 92

MICRO WATERPROOF

Бренд: Zodiac Страницы: 37

WATER-PRO MODULAR B-60

Бренд: ECO SISTEMS Страницы: 26

Бренд: Hyundai Страницы: 28

Бренд: Raveon Страницы: 40

Бренд: Baofeng Страницы: 56

Бренд: Bosscom Страницы: 18

Бренд: Raytheon Страницы: 117

Бренд: Humminbird Страницы: 16

Бренд: Humminbird Страницы: 26

MEGA 360 UNIVERSAL

Бренд: Humminbird Страницы: 38

Бренд: Binatone Страницы: 11

Бренд: Binatone Страницы: 13

Бренд: BK Radio Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды