Blueprint Subsea seatrac X100 Series страница 42 Скачать руководство пользователя

Страница: 42 / 140

SeaTrac Serial Command Interface Reference

Page 42

0x0E

CST_PROG_DATA_ERROR Returned

there is an error decoding data in

a firmware block.

0x0F

CST_PROG_CHECKSUM_ERROR Returned

if the specified checksum for the

firmware does not match the checksum
computed prior to performing the update.

Acoustic Transceiver Status Codes

0x30

CST_XCVR_BUSY

Returned if the transceiver cannot perform a
requested action as it is currently busy (i.e.
transmitting a message).

0x31

CST_XCVR_ID_REJECTED

Returned if the received message did not
match the specified transceiver ID (and
wasn’t a Sent-To-All), and the message has
been rejected.

0x32

CST_XCVR_CSUM_ERROR

Returned if received acoustic message’s
checksum was invalid, and the message has
been rejected.

0x33

CST_XCVR_LENGTH_ERROR Returned

if an error occurred with message

framing, meaning the end of the message has
not been received within the expected time.

0x34

CST_XCVR_RESP_TIMEOUT Returned

the transceiver has sent a request

message to a beacon, but no response has
been returned within the allotted waiting
period.

0x35

CST_XCVR_RESP_ERROR Returned

the transceiver has send a request

message to a beacon, but an error occurred
while receiving the response.

0x36

CST_XCVR_RESP_WRONG Returned

the transceiver has sent a request

message to a beacon, but received an
unexpected response from another beacon
while waiting.

0x37

CST_XCVR_PLOAD_ERROR Returned

protocol payload decoders, if the

payload can’t be parsed correctly.

0x3A

CST_XCVR_STATE_STOPPED Indicates

the

transceiver is in a stopped state.

0x3B

CST_XCVR_STATE_IDLE

Indicates the transceiver is in an idle state
waiting for reception or transmission to start.

0x3C

CST_XCVR_STATE_TX

Indicates the transceiver is in a transmitting
states.

0x3D

CST_XCVR_STATE_REQ

Indicates the transceiver is in a requesting
state, having transmitted a message and is
waiting for a response to be received.

Содержание seatrac X100 Series













































































































































Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды

Blueprint Subsea seatrac X100 Series, Руководство пользователя

Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды