Blueprint Subsea seatrac X100 Series страница 132 Скачать руководство пользователя

Страница: 132 / 140

SeaTrac Serial Command Interface Reference

Page 132

POSITION_DEPTH INT16

The

vertical

Depth distance component of the

remote beacon from the surface - computed from
the range, incoming signal angle, local beacon
depth, attitude and magnetic heading.

This value must be encoded in deci-meters, so
multiply the meters distance by 10 and truncate as
an integer.

Response Message Parameters

Parameter Type Description

MSG_ID

CID_E

Command

identification code

(CID_NAV_BEACON_POS_SEND)

STATUS

CST_E

Status code used to indicate if the command
executed successfully.
Valid values are…



CST_OK

The PING command is being sent.



CST_CMD_PARAM_INVALID

The DEST_ID parameter is invalid.



CST_CMD_PARAM_MISSING

The DEST_ID has not been specified correctly.



CST_XCVR_BUSY

The message cannot be sent as the acoustic
transceiver is busy performing another operation.

Содержание seatrac X100 Series













































































































































Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды

Blueprint Subsea seatrac X100 Series, Руководство пользователя

Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды