Blueprint Subsea seatrac X100 Series страница 126 Скачать руководство пользователя | Manualshive

Страница: 126 / 140

background image

SeaTrac Serial Command Interface Reference

Page 126

8.4.3.

CID_NAV_QUERY_RESP

The CID_NAV_QUERY_RESP status message is generated when the beacon receives back a
message from the remote beacon in response to a

CID_NAV_QUERY_SEND

In the response, the requested remote beacons information specified by the QUERY_FLAGS
parameter is encoded, and output via this message.

This message is a status message that may be sent by the beacon at any time (not in
response to a command message) depending on acoustic activity triggering a
transceiver event.

Note: By default the NAV protocol uses an enhanced USBL fix that returns the remote
beacons depth to a resolution of 1m, and this is used to augment the position fix.
However, if the QRY_DEPTH bit is specified in the sent QUERY_FLAGS field, the remote
beacon will return the depth to an resolution of 0.1m and use this value instead in the
position fix as well as returning it in the REMOTE_DEPTH field and FIX structure.

Status Message Parameters

Parameter Type Description

MSG_ID

Command

identification code

(CID_NAV_QUERY_RESP)

ACO_FIX

A Fix structure containing information relating to
the range and position of the beacon sending data.

See note above regarding enhanced depth
resolution when using the QRY_DEPTH flag.

QUERY_FLAGS

Bit mask that contains the fields the

CID_NAV_QUERY_SEND

message specified.

Depth Fields

If the message QUERY_FLAGS parameter contains the QRY_DEPTH bit (see

then the following fields are sequentially appended to the message record…

REMOTE_DEPTH

INT32

The remote beacons depth based on the measured
environmental pressure.
Values are encoded in deci-metres, so divide by 10
for a value in metres.

See note above regarding enhanced depth
resolution when using the QRY_DEPTH flag.

«
...
124
125
126
127
128
...
»

Содержание seatrac X100 Series













































































































































Отзывы:

Нет отзывов

Похожие инструкции для seatrac X100 Series

Бренд: Audiovox Страницы: 28

Бренд: Furuno Страницы: 10

Бренд: Sangean Страницы: 11

SoundWorks Radio 820HD

Бренд: Cambridge SoundWorks Страницы: 20

Бренд: Hytera Страницы: 33

Бренд: Imperial Страницы: 40

Бренд: Garmin Страницы: 20

Бренд: Curtis Страницы: 3

Бренд: Vertex Standard Страницы: 6

Бренд: Vertex Standard Страницы: 44

Бренд: Optimus Страницы: 12

Бренд: Harman Страницы: 2

HI-TARGET HD-MAX

Бренд: Hi-Target GPS Страницы: 177

Freedom Lite Marine 10/8

Бренд: Freedom Won Страницы: 26

Бренд: Böning Страницы: 65

SAILOR TT-3000E mini-C GMDSS System

Бренд: Thrane&Thrane Страницы: 97

Texas Ranger TR-127DX

Бренд: Ranger Communications Страницы: 29

Бренд: iHome Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды