Blueprint Subsea seatrac X100 Series страница 35 Скачать руководство пользователя

Страница: 35 / 140

SeaTrac Serial Command Interface Reference

Page 35

6.3.5.

CAL_ACTION_E (Calibration Actions)

The Calibration Action enumeration defines what operation the beacon should perform when a

CID_CAL_ACTION

command is issued. Valid operations are…

Value Symbolic

Name

Summary

0x00

CAL_ACC_DEFAULTS

Sets the current accelerometer calibration
coefficient values back to defaults.

0x01

CAL_ACC_RESET

Resets the accelerometer Min and Max filtered
limit values measured by the sensor (does not
modify the current calibration).

0x02

CAL_ACC_CALC

Calculates the new accelerometer calibration
coefficients from the measured sensor limit
values.

0x03

CAL_MAG_DEFAULTS

Sets the current magnetometer calibration
values back to defaults for Hard and Sort Iron
(does not clear the magnetic buffer).

0x04

CAL_MAG_RESET

Clears the magnetic calibration buffer (does
not modify the current calibration).

0x05

CAL_MAG_CALC

Calculate and apply a new Magnetometer
calibration from current magnetic buffer
values.

0x06

CAL_PRES_OFFSET_RESET

Reset the pressure offset back to zero Bar.

0x07

CAL_PRES_OFFSET_CALC

Sets the pressure offset from the current
measured pressure, zeroing the depth sensor
reading.

Содержание seatrac X100 Series













































































































































Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды

Blueprint Subsea seatrac X100 Series, Руководство пользователя

Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды