Blueprint Subsea seatrac X100 Series страница 104 Скачать руководство пользователя

Страница: 104 / 140

SeaTrac Serial Command Interface Reference

Page 104

7.6.10.

CID_XCVR_STATUS

The CID_XCVR_STATUS command can be used to determine the current operating state of the
acoustic transceiver modules.
It is particularly useful to use prior to issuing other commands that may start transmissions
(i.e.

CID_PING_SEND

CID_ECHO_SEND

etc.) to check that the transceiver is currently in the

IDLE state and can perform the operation.

Command Message Parameters

Parameter Type Description

MSG_ID

CID_E

Command

identification

code (CID_XCVR_STATUS)

Response Message Parameters

Parameter Type Description

MSG_ID

CID_E

Command

identification

code (CID_XCVR_STATUS)

STATUS

CST_E

Status code used to indicate if the command
executed successfully.
Valid values are…



CST_XCVR_STATE_STOPPED

Indicates the transceiver is in a stopped state.



CST_XCVR_STATE_IDLE

Indicates the transceiver is in an idle state waiting
for reception or transmission to start.



CST_XCVR_STATE_TX

Indicates the transceiver is in a transmitting states.



CST_XCVR_STATE_REQ

Indicates the transceiver is in a requesting state,
having transmitted a message and is waiting for a
response to be received.



CST_XCVR_STATE_RX

Indicates the transceiver is in a receiving state.



CST_XCVR_STATE_RESP

Indicates the transceiver is in a responding state,
where a message is being composed and the
“response time” period is being observed.

Содержание seatrac X100 Series













































































































































Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды

Blueprint Subsea seatrac X100 Series, Руководство пользователя

Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды