Blueprint Subsea seatrac X100 Series страница 66 Скачать руководство пользователя | Manualshive

Страница: 66 / 140

background image

SeaTrac Serial Command Interface Reference

Page 66

7.1.2.

CID_SYS_INFO

The CID_SYS_INFO command is used to receive hardware and firmware identification
information from the beacon. This information can then be used by external applications to
determine if firmware needs updating, or to determine support for Command Messages based
on the hardware type.

Command Message Parameters

Parameter Type Description

MSG_ID

Command

identification code (CID_SYS_INFO)

Response Message Parameters

Parameter Type

Description

MSG_ID

Command

identification code (CID_SYS_INFO)

SECONDS

UINT32

The number of seconds the beacon has been
powered up for.

SECTION

UINT8

The memory section that the current firmware is
executing in. Valid values are…



0 = Bootloader Application



1 = Main Application

HARDWARE

Structure containing details about the Beacon

hardware, including part number, revision and
unique serial number.

BOOT_FIRMWARE

Structure containing details about the Bootloader
firmware, including version, build and checksum
details.

MAIN_FIRMWARE

Structure containing details about the Main

Application firmware, including version, build and
checksum details.

«
...
64
65
66
67
68
...
»

Содержание seatrac X100 Series













































































































































Отзывы:

Нет отзывов

Похожие инструкции для seatrac X100 Series

Бренд: Yaesu Страницы: 43

REVERY R4 WFS-58

Бренд: Sangean Страницы: 87

Бренд: Grundig Страницы: 13

Бренд: MAJORITY Страницы: 24

Бренд: Furuno Страницы: 96

Бренд: NAVICOM Страницы: 32

Бренд: Arion Страницы: 31

Бренд: COMNET ERICSSON Страницы: 32

Бренд: Naxa Страницы: 11

Бренд: Heathkit Страницы: 78

Бренд: Yaesu Страницы: 34

Бренд: Volvo Страницы: 12

Бренд: vesper marine Страницы: 16

Бренд: vesper marine Страницы: 67

ECDIS NX Compact

Бренд: Raytheon Anschütz Страницы: 53

Бренд: Dual Страницы: 33

Бренд: Roadstar Страницы: 11

Бренд: Denver Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды