Blueprint Subsea seatrac X100 Series страница 19 Скачать руководство пользователя

Страница: 19 / 140

SeaTrac Serial Command Interface Reference

Page 19

Application Version = v1.0.1915

Application Checksum = 0x4DBF60E9

Pressure Sensor Id = 20905984

Pressure Sensor Type = PA

Pressure Sensor Calibrated = 2014-03-01

Pressure Sensor Min = 0.0 bar

Pressure Sensor Max = 200.0 bar

Ready...



At this point the beacon is ready to receive serial commands. Type “#0281C1” and
press return – this will send a

CID_SYS_INFO

command requesting hardware and

firmware information.



Something similar to the following information string should be returned (if not a
formatting error message/code will be returned – see

CST_E

for appropriate return

codes)…

$0234000000011B0301690E000000000000FF900301006901B7FAC5BFFF910301007A077504

63A973BA



The fields in the above message can then be decoded using the information given in
the

CID_SYS_INFO

command reference section of this document. Alternately, you

could use the SeaTrac Tools application to send the above command, and use the
“Journal” to decode the information fields as…

Received Len = 41 bytes (in 83 chars)

Received Data =

"$0234000000011B0301690E000000000000FF900301006901B7FAC5BFFF910301007A07750

463A973BA"

CmdId = SYS_INFO (0x02)

Uptime = 0x00000034 (52)

Section = 0x01 (1)

HardwarePartNumber = 0x031B (795)

HardwarePartRevision = 0x01 (1)

HardwareSerialNumber = 0x00000E69 (3689)

HardwareFlags = 0x00000000 (0)

BootValid = TRUE

BootPartNumber = 0x0390 (912)

BootVersionMajor = 0x01 (1)

BootVersionMinor = 0x00 (0)

BootVersionBuild = 0x0169 (361)

BootChecksum = 0xBFC5FAB7 (3217423031)

AppValid = TRUE

AppPartNumber = 0x0391 (913)

AppVersionMajor = 0x01 (1)

AppVersionMinor = 0x00 (0)

AppVersionBuild = 0x077A (1914)

AppChecksum = 0xA9630475 (2841838709)

4.4.

Fetching, Updating and Storing Settings

Using a process similar to that described in section 4.3 above, you can make you application
change the beacon settings using the following sequence of commands…

Содержание seatrac X100 Series













































































































































Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды

Blueprint Subsea seatrac X100 Series, Руководство пользователя

Результаты поиска

Содержание seatrac X100 Series

Отзывы:

Похожие инструкции для seatrac X100 Series

Бренды по названию

Популярные бренды