Black Box PI750A Скачать руководство пользователя страница 52

Страница: 52 / 173

MULTIPORT SPOOLER VIII (4-, 8-, and 12-Port Models)

6. Tell MPSSETUP which of the PC’s ports is connected to the MPS-VIII.

If the connected PC port is a serial port, set the port’s parameters.

7. Tell MPSSETUP which MPS-VIII model is connected to the PC.

8. If you are installing the UCTP, proceed to Step 9. If you aren’t, go to

Step 12.

9. Choose the UCTP menu level.

10. Decide whether or not the UCTP will function as a resident (TSR)

or nonresident program.

11. Choose the video interface, set the break, set the token, and select

hotkeys.

12. If you are installing MPSDOS, proceed to Step 13. If you aren’t, go to

Step 17.

13. Set the redirection for each port, and (if you want to) define strings for

the ports.

14. Set the timeout.

15. Choose whether or not returned messages will be verified.

16. If you want to, select a port and print its configuration.

17. Confirm the installation.

18. Return to DOS or reboot the PC.

This completes the installation process. From this point on, you should

able to select output (printer) ports from inside your applications.

Содержание PI750A













































































































































































Результаты поиска

Содержание PI750A

Отзывы:

Похожие инструкции для PI750A

Бренды по названию

Популярные бренды

Black Box PI750A, Руководство пользователя

Результаты поиска

Содержание PI750A

Отзывы:

Похожие инструкции для PI750A

Бренды по названию

Популярные бренды