Black Box PI750A Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 173

background image

94

MULTIPORT SPOOLER VIII (4-, 8-, and 12-Port Models)

Unable to copy MPSWIN.DRV
Unable to copy MPSWIN.INI
Unable to copy MPSWIN.HLP
Unable to copy SETUPWIN.EXE
Unable to copy EDITOR.EXE
Unable to copy EDITOR.ICO
Unable to copy README.WIN
Unable to copy SYSTEM.INI
Unable to copy WIN.INI
Unable to copy WINUCTP.EXE
Unable to copy WINUCTP.PRO

Either the source disk and directory are not valid, the file is not on the floppy
disk, or the hard disk is full.

Unable to create the MPSWIN subdirectory

The installation program cannot create the MPSWIN subdirectory. Make sure
your hard disk is not full.

Unable to create MPSWIN group

The installation program cannot communicate with the Windows Program
Manager. Consequently, the MPSWIN Applications window cannot be
created.

Unable to start up the automatic loading of the WINUCTP program

The installation program cannot open the WIN.INI file.

Unable to insert the new port in WIN.INI file

The installation program cannot create the COM5 to COM9 phantom ports.

Unable to install the MPSWIN interface

The installation program cannot open the SYSTEM.INI file.

Unable to modify spooler status

General error. The installation program cannot open the WIN.INI file.

«
...
100
101
102
103
104
...
»

Содержание PI750A














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PI750A

Бренд: Water Witch Страницы: 2

MMAC-Plus 9G426-02

Бренд: Cabletron Systems Страницы: 12

MMAC-Plus 9F310-02

Бренд: Cabletron Systems Страницы: 4

Бренд: Cabletron Systems Страницы: 16

Бренд: cable matters Страницы: 4

Бренд: CableCreation Страницы: 7

SmartSwitch 6500

Бренд: Cabletron Systems Страницы: 150

MMAC-Plus 9H421-12

Бренд: Cabletron Systems Страницы: 38

Бренд: Cabletron Systems Страницы: 86

MMAC-Plus 9T125-24

Бренд: Cabletron Systems Страницы: 30

7C03 MMAC SmartSWITCH

Бренд: Cabletron Systems Страницы: 16

Бренд: United Electric Controls Страницы: 6

Бренд: Tecsis Страницы: 2

Бренд: Extron electronics Страницы: 2

A99-BAI-ACSF-UGKIT

Бренд: Westell Страницы: 3

Бренд: DANLERS Страницы: 2

Бренд: V7 Страницы: 35

Бренд: Datavideo Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды