Bennett HIGH FLOW H35, Инструкция по эксплуатации

Страница: 14 / 98

Product Introduction
Bennett HF H35 Instruction Manual 10
POWER FAILURE (LAST SALE RECALL)
If an AC power failure occurs, the dispenser will display the last sale in progress at the time
of the failure.
Note: The dispenser valves close and fueling is stopped. The main display
will alternate between the last sale amount and mass as shown in Figure 1.4 and the AC
OFF message as shown in Figure 1.3 for 15 minutes. After 15 minutes, the display will go
blank until normal power returns. If power is returned, the display will return to its idle
state.
Figure 1.4 – Last Sale Recall
TOTALS SWITCH
The totals switch is a magnetic reed switch. The switch is located directly behind the mass units screen on the main display area as shown
in
Figure 1.5 . Note: If a pump handle is turned on during this operation, the display returns to idle.
To enter the Totals Mode, follow this procedure:
1. Hold the black Access Magnet over the mass units
KILOGRAM
print beside the Main Display.
This will display all Mode 1, Mode 2, and Mode 26 shift totals.
2. Once the totals mode is entered, the next totals are displayed by tapping the magnet over
the mass units
KILOGRAM
print beside the main display. By successively tapping over the
mass units
KILOGRAM
print, all totals can be displayed.
3. If the magnet is not tapped over the mass units
KILOGRAM
print for 30 seconds, the display
will return to its idle state. Refer to Menu Codes 1 and 26 for more information.
Figure 1.5 – Totals Switch
(2) PAYMENT PANEL WITH 7” OR 10.5” DISPLAY
A 7” or a 10.5” large display is used to view guided instructions during a fill and to
process payments. Power is provided to the display through the SBC2 board. Refer
to the SSP Large Display w/ SBC2 Programming manual for additional information.
Contact Bennett Technical Support at 1-800-423-6638 for further information.
Once the module installed, programmed, and configured properly by the POS. The
module will be ready for use.
1. Training instructions will be shown on the display before and/during the
fueling process. The idle screen shown in
Figure 1.6 is an example of how of
the module prompts the user with guided instructions.
2.
Follow the prompts on the display and continue the fueling process. Use the
left/right soft keys to select an option corresponding to a left (<) or right arrow
(>) shown on the display.
Note: The user must make a selection to continue
the fueling process. If a selection is not made, the screen will timeout and
return to the start screen.
3. Press < CANCEL > to stop fueling and to end the guided training.
Figure 1.6 - Guided instructions splash screen
(3) PRODUCT SELECT BUTTONS
The customer must select the grade to be pumped before the dispenser will operate. The product select buttons are located below the
payment display, card reader, and numeric keypad.
(4) NOZZLE BOOT & LOCK
The nozzle boot is located on the side of the dispenser. Note: The hydrogen nozzle lever locks through the nozzle hook. A lock can be used
to lock out the dispenser even though nozzle can be removed from the boot. The nozzle boot switch will not activate the dispenser. The
lock can be inserted through the nozzle hook and lever.
To operate the dispenser, follow this procedure:
1. Remove the nozzle from the holder. Note: A lift lever will need to be lifted up.
2. Once the lift lever is lifted, a switch tells the CPU Board that the nozzle is removed from the holder.
(5) KEYPAD
The Bennett hydrogen dispenser features an optional keypad for entering credit card information.
Sale $
43.05
Kilograms 3.331
Access Magnet
Sale $ 0.00
Kilograms
0.000